Moog Videolarm WS2C-50NF-X2 Especificações

Consulte online ou descarregue Especificações para Câmaras de segurança Moog Videolarm WS2C-50NF-X2. Moog Videolarm WS2C-50NA surveillance camera Manual do Utilizador

  • Descarregar
  • Adicionar aos meus manuais
  • Imprimir
Vista de página 0
PRODUCT INSTRUCTIONS
INSTALLATION PREPARATION
1. Determine the mounting location. Be sure that you'll be
mounting to a secure wall or ceiling. We also recommend
that for outdoor applications the housing be mounted in a
protected area.
2. Complete all wire and conduit runs prior to installation.
3. The WS2 and WS4 are designed to be mounted in a
standard deep double-gang box.
4. IMPORTANT REMINDER: For outdoor applications it is
strongly recommended that you use sealant. Place a light
bead of sealant around the perimeter of the back of the
housing and around the head of each screw connecting the
housing to the double-gang box.
REVISION DATE: 02-02-2009
Depending on the voltage being used, refer to one of the formulas
below to select the correct power supply for cameras connected in
parallel (positive to positive, negative to negative):
Total current for a 12 VDC system:
TOTAL CURRENT = (350mA x total number of cameras)
Total current for a 24 VAC system:
TOTAL CURRENT = (202mA x total number of cameras)
VOLTAGE CURRENT POWER
12 VDC 350mA 4.2W
24 VAC 202mA 4.8W
CABLE AND POWER GUIDELINES
(Detailed info on Page 12)
This chart shows the proper current needed for power supplies for
Warrior Series cameras. Use Class 2 Power only. Output voltage
must be between 12-28 VDC or 15-28 VAC.
81-IN5236-06154 WARRIOR 2 & 4
WS2(T/C)-XXXX / WS4-XXXX
Figure 1
INSTALLATION PROCEDURE
1. Mount a double-gang box (not provided) using standard proce-
dures. Pull power and video wires through the gang box.
2. Using the security tool provided, loosen the four security
fasteners and remove the housing top.
NOTE: The housing top is held to the base by a lanyard.
3. Remove the bracket assembly by removing the (2) 10-32 screws
(Figure 1).
NOTE: The camera is connected to the power board. Be
careful not to pull the wire loose.
TABLE OF CONTENTS
Cable and Power Guidelines 1, 12
Installation Preparation 1
Installation Procedure 1
Wiring 2
Optional Warrior Test Monitor Cable 2
Camera Bracket Setup 2
Camera Focusing 3
Camera Settings 3
Completion of Installation 5
Dome/Window Care 5
NVT Instructions 6
IFS Instructions 7
Warranty Information 8
Service and Safeguard Information 9
Troubleshooting 10
Exploded View WS2 11
Replacement Parts WS2 12
Exploded View WS4 13
Replacement Parts WS4 14
© 2009, Videolarm, Inc. All Rights Reserved
Vista de página 0
1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - PRODUCT INSTRUCTIONS

PRODUCT INSTRUCTIONSINSTALLATION PREPARATION1. Determine the mounting location. Be sure that you'll be mounting to a secure wall or ceilin

Página 2 - WIRING (Figure 2)

AC VoltmeterCamera MonitorBridge TapNV-213ANV-213A- 11 -NVT TROUBLESHOOTINGIf you are experiencing problems, attempt to simplify your setup. Test each

Página 3 - CAMERA SETTINGS

- 12 -Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (po

Página 4

6543217- 13 -WS2 - Exploded Diagram

Página 5 - COMPLETION OF INSTALLATION

- 14 -WS2 - Replacement Parts ListPart Number Description1 RPWS2010 WARRIOR 2 & 4 BASE ASSEMBLY 2 RPWS2020 WARRIOR 2 & 4 CARRIAGE ASSEMBLY KIT

Página 6 - ADDENDUM 1

7654321- 15 -WS4 - Exploded Diagram

Página 7 - ADDENDUM 2

- 16 -WS4 - Replacement Parts ListPart Number Description1 RPWS2010 WARRIOR 2 & 4 BASE ASSEMBLY 2 RPWS2020 WARRIOR 2 & 4 CARRIAGE ASSEMBLY KIT

Página 8 - 1-800-554-1124

Product Registration/WarrantyThank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the highes

Página 9 - TROUBLESHOOTING

- 2 -CAMERA BRACKET SETUP (Figure 5)Reattach the bracket assembly to the back box using the two 10-32 x 3/8" screws. NOTE: For ceiling mount ap

Página 10 - NVT TROUBLESHOOTING

- 3 -Figure 6CAMERA FOCUSING Fixed Lens: Loosen the set screw in the lens mount and to manually rotate the lens until a clear picture is ach

Página 11 - CABLE AND POWER GUIDELINES

- 4 -The operational settings for the camera are defi ned by ten dip switches located on the PC Board (Figure 9). Moving the switches to the on positio

Página 12 - Exploded Diagram

- 5 -NOTE: This hi-res color camera uses a 1/4" chip and a 3-6mm auto iris lens. It is comparable to a 1/3" chip using a

Página 13 - Replacement Parts List

- 6 -Wiring NotesWire — What to DO1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or thicker, stranded or solid, Category 2, 3, 4, or

Página 14

250 ft 250 ft 3 4 5 8 13 1300 ft300 ft4 5 6 10 16 1400 ft400 ft5 6 8 13 21 1500 ft500 ft6 8 10 16 26 1600 ft600 ft8 10 12 19 31 1800 ft800 ft10 13 16

Página 15

! CAUTIONRISK OF ELECTRIC SHOCK! CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT EXPOSE COMPONENTS TO WATER OR MOISTURE.SAFETY PRECAUTIONS

Página 16 - Online Option 2: Mail-In

Power SupplyPower APower BCameraAssemblyPrimaryPowerVideo SignalVideo ShieldMonitor- 10 -(Ground Return)Figure A Ground LoopTROUBLESHOOTINGIf you expe

Comentários a estes Manuais

Sem comentários