Moog Videolarm WS1C-50NA-X2 Especificações descarregar pdf

PRODUCT INSTRUCTIONS

INSTALLATION PREPARATION

1. Mount to a secure wall or ceiling. For outdoor application we also

recommend that the housing be mounted in a protected area.

2. Complete all wire and conduit runs prior to installation.

3. Determine the mounting method:

A. Mount directly to a wall or ceiling.

B. Mount to a standard 4-square electrical box (not provided).

4. IMPORTANT REMINDER: For outdoor applications attach the

provided gasket to the back of the housing (Figure 1). WE

STRONGLY RECOMMEND USING A sealant. Place a light

bead of sealant around the perimeter of the gasket surface and

around the head of each screw.

Conduit outlet

(Place on

bottom in

protected

outdoor

applications)

Figure 2

Mounting Holes

REVISION DATE: 11-09-2010

INSTALLATION PROCEDURE

1. Using the security tool provided, loosen the four security fasten-

ers and remove the housing top. NOTE: The housing top is held

to the base by a lanyard.

2. Determine which side the conduit outlet will be located on: Top,

bottom, left, or right.

NOTE: In protected outdoor applications place the conduit

outlet in the bottom position, facing the ground.

3. Position the housing in the desired location and mark the four

mounting holes (Figure 2).

Figure 1

Set screw

4. Pull video and power wires through the desired conduit access

hole. Use the correct conduit plug to cover the unused hole.

NOTE: For outdoor applications use Teon™ tape on the

threads.

A. Use the 1/2" conduit plug to cover the 1/2"

threaded hole. Attach using a at head screwdriver.

B. Use the 3/4" conduit plug to cover the 3/4"

threaded

hole. To do this loosen the 6-32 set screw that

holds the connector in, remove the connector and

replace it with the plug. Once the plug is tightened

down, retighten the set screw.

NOTE: Make sure that the conduit plug and set screw are

securely tightened to help prevent tampering.

Depending on the voltage being used, refer to one of the formulas

below to select the correct power supply for cameras connected

in parallel (positive to positive, negative to negative):

Total current for a 12 VDC system:

TOTAL CURRENT = (350mA x total number of cameras)

Total current for a 24 VAC system:

TOTAL CURRENT = (202mA x total number of cameras)

VOLTAGE CURRENT POWER

12 VDC 350mA 4.2W

24 VAC 202mA 4.8W

CABLE AND POWER GUIDELINES

(Detailed info on Page 12)

This chart shows the proper current needed for power supplies for

Warrior Series cameras. Use Class 2 Power only. Input voltage

must be between 12-28 VDC or 15-28 VAC.

81-IN5217 WARRIOR 1 & 3

WS1(T/C) / WS3

5. Attach the housing using #10 mounting screws, placing the

provided mounting pads against the head of the screw.

NOTE: When installing outdoors, remember to use sealant

around the screws and the back of the housing.

TABLE OF CONTENTS

Cable and Power Guidelines 1, 12

Installation Preparation 1

Installation Procedure 1

Wiring 2

Optional Warrior Test Monitor Cable 2

Camera Bracket Setup 2

Camera Focusing 3

Camera Settings 3

Completion of Installation 5

Dome/Window Care 5

NVT Instructions 6

IFS Instructions 7

Warranty Information 8

Service and Safeguard Information 9

Troubleshooting 10

Exploded View WS1 13

Replacement Parts List WS1 14

Exploded View WS3 15

Replacement Parts List WS3 16

1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - 81-IN5217 WARRIOR 1 & 3

PRODUCT INSTRUCTIONSINSTALLATION PREPARATION1. Mount to a secure wall or ceiling. For outdoor application we also recommend that the housing be m

Página 2 - (Part # - WSTMC)

- 10 -WS1 - Exploded Diagram

Página 3 - CAMERA SETTINGS

- 11 -Part Number Description Dealer Cost1 RPWS1010 PACKET ASSEMBLY WARRIOR 1& 3 HOUSINGS $172 RPWS1020 WARRIOR 1 & 3 BASE ASSEMBLY $453 RPWS

Página 4 - DOME/WINDOW CARE

- 12 -WS3 Exploded Diagram

Página 5 - ADDENDUM 1

- 13 -WS3Replacement Parts ListPart Number Description Dealer Cost1 RPWS1010 PACKET ASSEMBLY WARRIOR 1 & 3 HOUSINGS $172 RPWS1020 WARRIOR 1 &

Página 6 - ADDENDUM 2

- 14 -IMPORTANT SAFEGUARDS SAFETY PRECAUTIONSUNPACKINGSERVICE1 Read these instructions.2 Keep these instructions. 3 Heed all warnings 4 F

Página 7 - TROUBLESHOOTING

- 15 -LIMITED WARRANTYFOR VIDEOLARM INC. PRODUCTSVIDEOLARM INC. warrants this Product to be free from defectsin material or workmanship,as follows:PRO

Página 8 - AC Voltmeter

- 16 -Product Registration/WarrantyThank you for choosing Videolarm. We value your patronage and are solely committed to providing you with only the

Página 9 - CABLE AND POWER GUIDELINES

- 2 -CAMERA BRACKET SETUPOnce the housing is installed, the three axis camera bracket allows the camera to be adjusted to the desired viewing location

Página 10 - Exploded Diagram

- 3 -Figure 7CAMERA FOCUSING Fixed Lens: Loosen the set screw in the lens mount and to manually rotate the lens until a clear picture is ach

Página 11 - Replacement Parts List

- 4 -1. A cardboard template is included to test the adjustment of your lens/bracket setup before reattaching the housing top. Place the tem

Página 12

- 5 -Wiring NotesWire — What to DO1. DO use point-to-point Unshielded Twisted Pair wire, gauge 24 or thicker, stranded or solid, Category 2, 3, 4, or

Página 13

250 ft  3  4  5  8  13 W300 ft  4  5  6  10  16 W400 ft 5  6  8  13  21 W500 ft 6  8  10  16  26 W600 ft 8  10  12  19

Página 14 - DO NOT OPEN

Power SupplyPower APower BCameraAssemblyPrimaryPowerVideo SignalVideo ShieldMonitor- 7 -(Ground Return)Figure A Ground LoopTROUBLESHOOTINGIf you exp

Página 15

AC VoltmeterCameraMonitorBridge TapNV-213ANV-213A- 8 -NVT TROUBLESHOOTINGIf you are experiencing problems, attempt to simplify your setup. Test each

Página 16 - Online Option 2: Mail-In

- 9 -Depending on the voltage being used, refer to one of the formulas below to select the correct power supply for cameras connected in parallel (pos

Comentários a estes Manuais

Sem comentários

Moog Videolarm WS1C-50NA-X2 Especificações

Consulte online ou descarregue Especificações para Câmaras de segurança Moog Videolarm WS1C-50NA-X2. Moog Videolarm WS1C-50NA surveillance camera Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Câmaras de segurança Moog Videolarm WS1C-50NA-X2